AnyLink2 2.4GHz Radio Adapter

Unlocks your transmitter’s full potential!

Your transmitter alone can only do so much. But your transmitter with the AnyLink2 2.4GHz Radio Adapter can work wonders.
Adding it enables your transmitter to broadcast a true, 2.4GHz signal and operate with the utter dependability of the best in 2.4GHz technology.
The AnyLink2 adapter is compatible with an incredibly wide range of transmitters, as well as incredibly simple and easy to install.
And once it is installed, your transmitter can fly:

  • All Tx-R (Transmitter-Ready) aircraft, and
  • Any aircraft with a 2.4GHz SLT receiver

That includes huge scale aircraft, park flyers and helis, whether they use glow, gasoline or electric power.

Tactic SLT Secure Link Technology Tx-R Transmitter Ready

Product Flier Manual

But those aren't the only amazing things about AnyLink2. Here are three more:

  • AnyLink2 works with virtually any transmitter, regardless of brand, band or modulation. That includes old favorites, like-new transmitters and even non-2.4GHz systems
  • AnyLink2 transforms your transmitter into a frequency-hopping, spread-spectrum system. It uses SLT — the same, dependability-proven protocol used in all Tactic transmitters and receivers.
  • AnyLink2 offers all of the convenience, versatility and benefits listed above for far less than the cost of a new 2.4GHz radio system — and for that matter, for less than the cost of most 2.4GHz receivers, as well.
  • AnyLink2 offers even more than the original AnyLink, including:
    • Compatibility with even more transmitters, including many Airtronics® transmitters.
    • A replaceable, rechargeable 1S LiPo battery and USB charger. The battery fits inside the AnyLink2 and provides 15 hours of flying time per charge. And if you use the included charger, it takes less than an hour to recharge.
    • Three adapter cables. Redesigned to work with even more transmitters — and equipped with headphone-type connectors for easy, plug-in installation and solid, connections.
    • Cleaner, easier installs for JR® and Spektrum® owners. You just plug one end into your radio, the other into the AnyLink2 and you're done!
    • Easy mapping. Just push the MODE button until the LED appears opposite the letter code for your radio!
    • Includes built-in clip that snaps onto metal carrying handles plus hard locking mounting strips for backplate mounting.
Specifications:   TACJ2005
Frequencies:   2.403 – 2.483GHz FHSS
Channels:   Six
Input Power:   3.3-4.20V, < 150mAh (provided by 1S, 3.7V 450mAh LiPo pack)
Power Indicator:   LED with audible tones
Inactivity Alarm:   5 minutes
Low-Voltage Alarm:   Audible Tones (@3.25V)
Output Power:   <0.1W
Dimensions:   2.68 x 1.46 x 0.85 in (68 x 37 x 25 mm)
Weight:   1.62 oz (46 g)
Requires:   Flight transmitter with DSC or trainer jack

Can the AnyLink2 unlock the full potential of your transmitter? Find out by checking the AnyLink Compatibility Chart.

Adapter Cables

Virtually all popular transmitters are compatible with AnyLink2. Many require only the adapter cables included with the AnyLink2: TACM0010, TACM0011 and TACM0012. Three optional adapter cables are available separately. Please note: Adapter cables for the original AnyLink and the AnyLink2 are not cross-compatible.

Adapter Cable TACM0010
TACM0010 JR®/Spektrum®
Transmitter Compatibility

Adapter Cable TACM0011
TACM0011 Futaba® Square
Transmitter Compatibility

Adapter Cable TACM0012
TACM0012 Spektrum/Hitec®
Transmitter Compatibility

Optional Adapter Cables

Adapter Cable TACM0013
TACM0013 Futaba/Hitec Round
Transmitter Compatibility

Adapter Cable TACM0014
TACM0014 Airtronics® SD Series
Transmitter Compatibility

Adapter Cable TACM0012
TACM0016 Airtronics 5-Pin Round
Transmitter Compatibility

Batteries and Chargers

AnyLink2 TC10 USB 1S 450mAh LiPo Battery Charger TACP0010
TACP0010 AnyLink2 TC10 USB 1S 450mAh LiPo Battery Charger

AnyLink2 LiPo 1S 3.7V 450mAh 25C TACP0011
TACP0011 Tactic AnyLink2 LiPo 1S 3.7V 450mAh 25C


The AnyLink2 2.4GHz Radio Adapter is compatible with all SLT receivers and virtually all flight transmitters, regardless of brand, band or modulation. Transmitters must have a trainer or DSC jack. For more information on AnyLink2, transmitter compatibility or requirements, see the Compatibility chart. All trademarks are the property of their respective owners.

© 2006-2017 Tactic, a Hobbico company. Terms of Use Privacy Statement

E-Bulletin Follow Hobbico on YouTube Follow Tactic on Facebook Follow Hobbico on Instagram Follow Hobbico on Twitter Follow Hobbico on Google+